Professional control of your appliances!
Commercial Info Features The X-10 DIN Rail Switch is a remote controlled relay. Mounted on a DIN rail in the main distribution box, it switches hard-wired circuits with several wall switches (e.g. hallway lighting). The internal relay can be controlled by an X-10 controller/interface or by external contacts (wall switches). 3600 Watt Use & Applications Can be controlled by any X-10 Controller or different types of Wall switches. This unit can replace any pulse contact relay that is commonly used for multi switched hall and entry lighting. In discrete locations, e.g. kitchen lighting, you may prefer to install AD10 in a small sub-junction box.
Features The X-10 DIN Rail Switch is a remote controlled relay. Mounted on a DIN rail in the main distribution box, it switches hard-wired circuits with several wall switches (e.g. hallway lighting). The internal relay can be controlled by an X-10 controller/interface or by external contacts (wall switches). 3600 Watt Use & Applications Can be controlled by any X-10 Controller or different types of Wall switches. This unit can replace any pulse contact relay that is commonly used for multi switched hall and entry lighting. In discrete locations, e.g. kitchen lighting, you may prefer to install AD10 in a small sub-junction box.
Use & Applications Can be controlled by any X-10 Controller or different types of Wall switches. This unit can replace any pulse contact relay that is commonly used for multi switched hall and entry lighting. In discrete locations, e.g. kitchen lighting, you may prefer to install AD10 in a small sub-junction box.
High quality modules for dimming of your lights!
Commercial Info Features First European product with "windowed AGC for improved PLC reliability in adverse environments. Designed to operate with 230V and 12V lighting including halogen. Remembers its light level for smooth dimming and brightening Soft (fixed) start and stop with STANDARD "X10" and programmable start and stop rates with PROFESSIONAL "X10" protocol. Use & Applications The X-10 DIN rail dimmer (LD11) is a 700 W receiver module that serves as remote controlled dimmer. Mounted on the DIN rail in the mains distribution box, it dims/switches hard -wired circuits with several wall switches (e.g. living room lighting). It is designed to operate with 230 V and 12 V lighting including halogen. The LD 11 can be turned on/off, and brightened/dimmed either by an X-10 controller or by external momentary action switches connected to terminal 2 - maximum connected cable length is 30 meters. The LD11 responds to "standard" X-10 that is: "All lights on" or "All units off" from any X-10 controller set to its house code regardless of unit code or alternatively individual unit control by "On", "Off", "Bright" and "Dim". The LD11 also responds to "professional X-10". Combined with the memory dim feature, the LD11 can change the room lighting instantly or progressively. This unit is especially designed for scene lighting where very often the lighting is 12 V halogen, commonly used in living room, study/reading rooms. The unit can be installed in sub-junction boxes for discrete control.
Features First European product with "windowed AGC for improved PLC reliability in adverse environments. Designed to operate with 230V and 12V lighting including halogen. Remembers its light level for smooth dimming and brightening Soft (fixed) start and stop with STANDARD "X10" and programmable start and stop rates with PROFESSIONAL "X10" protocol. Use & Applications The X-10 DIN rail dimmer (LD11) is a 700 W receiver module that serves as remote controlled dimmer. Mounted on the DIN rail in the mains distribution box, it dims/switches hard -wired circuits with several wall switches (e.g. living room lighting). It is designed to operate with 230 V and 12 V lighting including halogen. The LD 11 can be turned on/off, and brightened/dimmed either by an X-10 controller or by external momentary action switches connected to terminal 2 - maximum connected cable length is 30 meters. The LD11 responds to "standard" X-10 that is: "All lights on" or "All units off" from any X-10 controller set to its house code regardless of unit code or alternatively individual unit control by "On", "Off", "Bright" and "Dim". The LD11 also responds to "professional X-10". Combined with the memory dim feature, the LD11 can change the room lighting instantly or progressively. This unit is especially designed for scene lighting where very often the lighting is 12 V halogen, commonly used in living room, study/reading rooms. The unit can be installed in sub-junction boxes for discrete control.
Use & Applications The X-10 DIN rail dimmer (LD11) is a 700 W receiver module that serves as remote controlled dimmer. Mounted on the DIN rail in the mains distribution box, it dims/switches hard -wired circuits with several wall switches (e.g. living room lighting). It is designed to operate with 230 V and 12 V lighting including halogen. The LD 11 can be turned on/off, and brightened/dimmed either by an X-10 controller or by external momentary action switches connected to terminal 2 - maximum connected cable length is 30 meters. The LD11 responds to "standard" X-10 that is: "All lights on" or "All units off" from any X-10 controller set to its house code regardless of unit code or alternatively individual unit control by "On", "Off", "Bright" and "Dim". The LD11 also responds to "professional X-10". Combined with the memory dim feature, the LD11 can change the room lighting instantly or progressively. This unit is especially designed for scene lighting where very often the lighting is 12 V halogen, commonly used in living room, study/reading rooms. The unit can be installed in sub-junction boxes for discrete control.
FILTER/COUPLER - FD10
Couples signals across phases!
Commercial Info Prevents X-10 signals from leaving/entering the home. Couples signals across phases. Features This DIN-rail Filter/Coupler is intended to filter out RFI suppression components when they tend to reduce the range of Time control signals. Use & Applications The signals transmission of high frequency pulses via the mains network can be affected by active or passive interferences. When used correctly the Filter/Coupler will extensively suppress these interferences. Typical active interference sources are appliances that do not dispose of a regular interference suppression according to the norms, as well as wireless intercommunication systems which use borne signaling, as they transmit high frequency signal interferences into the mains network. Remaining interferences generated within the house network are without significance as the special dynamic filtering techniques of the X-10 system ensure undisturbed performance. The Filter/Coupler also includes the ability to couple X-10 signals across phases. For installation with three phases, use three Filter/Couplers and couple the filters by connecting their terminals K to the next phase, respectively.
Features This DIN-rail Filter/Coupler is intended to filter out RFI suppression components when they tend to reduce the range of Time control signals.
Use & Applications The signals transmission of high frequency pulses via the mains network can be affected by active or passive interferences. When used correctly the Filter/Coupler will extensively suppress these interferences. Typical active interference sources are appliances that do not dispose of a regular interference suppression according to the norms, as well as wireless intercommunication systems which use borne signaling, as they transmit high frequency signal interferences into the mains network. Remaining interferences generated within the house network are without significance as the special dynamic filtering techniques of the X-10 system ensure undisturbed performance. The Filter/Coupler also includes the ability to couple X-10 signals across phases. For installation with three phases, use three Filter/Couplers and couple the filters by connecting their terminals K to the next phase, respectively.
Keep unwanted X-10 signals out of your house
Features The Signal Blocker keeps extraneous noise and X-10 signals which could interfere with your own X-10 signals from entering or leaving your house.
Use & Applications Ideal for apartment buildings and X-110 systems close to one another.
Allows almost anything to send X-10 signals!
Features This plug-in module sends an X-10 signal to other X-10 receivers/modules when a contact closure is made or by a low voltage input (6-18V AC, DC or Audio). It can also be set to 3 different modes; to turn all the lights on, flash all the lights or turn on selected lights and/or appliances set on the same house code. It can be triggered by a dry contact closure or a low voltage input (6-18V AC, DC or Audio). You can even create your own security system with the Powerflash. Connects to an existing burglar alarm system and flashes lights connected to lamp modules and wall switch modules when the alarm trips. Triggered by a contact closure or low voltage input (6-18V AC, DC or audio). Connects to an existing alarm system and turns on lights when the alarm trips. It has 3 modes of operation: In Mode 1 the Burglar Alarm Interface will turn ON ALL lamp modules and wall switch modules set to its Housecode and will also turn ON any other modules set to its Unit Code, a stereo connected to an appliance module for example. All lamp modules and wall switch modules are left in the ON state when the alarm is de-activated but the modules set to the same Unit Code as the Burglar Alarm Interface will be turned OFF. In Mode 2 the Burglar Alarm Interface will FLASH all lights connected to lamp modules or wall switch modules. All lamp and wall switch modules will be left in the ON state when the alarm is de-activated but appliance modules set to the same Housecode as the Burglar Alarm Interface will be turned OFF. In Mode 3 the Burglar Alarm Interface will turn ON all modules set to the same Housecode and Unit Code as the interface. All modules set to the same Housecode and Unit Code as the Burglar Alarm Interface will be turned OFF when the alarm is de-activated. Mode 3 is the same as mode 1 except that the interface does not send the All Lights On code to turn on ALL lamp modules and wall switch modules set to the same Housecode as the interface. The interface can be set to be triggered by either a low voltage input (6-18 volts AC, DC or audio) or a dry contact closure. You could also trigger it from an alarm which has an outlet for switching a 120V lamp by using this outlet to control a 120V relay, then use the contacts of the relay to trigger the interface (in the dry contact mode). The Burglar Alarm Interface has a test button which allows you to activate it whether or not it is connected to an alarm system. The ALL OFF button allows you to turn off anything which has been turned on by the interface.
Use & Applications - Create your own security system - Automatically turns on lights, music,... when door opens - Turns on devices when alarm is tripped - Flash all the lights in your home when your existing burglar alarm is tripped. · Blast your stereo when your alarm trips. · Connect the Burglar Alarm Interface directly to a magnetic switch to turn on lights when a door or window opens, i.e. you don't have to own a burglar alarm system. · Trigger it from sensors such as a photo cell to turn on lights when it gets dark. · From a motion detector to turn on lights when someone enters a room. · From a microphone to turn on lights or appliances when a sound from an intruder is detected. · From a moisture sensor to sound an alarm if your basement is flooded. · From a garage door opener to turn on lights when you open your garage door, etc. Some of these applications may require some additional components such as relays, etc. to interface to the Burglar Alarm Interface but virtually anything which gives, or can be made to give, either a contact closure or a low voltage output between 6 and 18 volts AC, DC or audio can be used to trigger the Burglar Alarm Interface.
Professional X-10 Signal Repeater
Commercial Info Features The Coupler / Repeater is applied in case of severe system attenuation or when the distance between Controller and Module (Receiver) is too long. After signal reconditioning, this device, after having amplified the signal, transmits it on all 3 phases of the connected network. The Repeater/Coupler is suitable for handling switching operations between widely spaced sections prevailing in complex wiring systems. Here this device can also be used as a coupler in connection with a twin-core control line. The signals arriving via the line are amplified and retransmitted in the filtered X-10 signal circuit. Use & Applications
Features The Coupler / Repeater is applied in case of severe system attenuation or when the distance between Controller and Module (Receiver) is too long. After signal reconditioning, this device, after having amplified the signal, transmits it on all 3 phases of the connected network. The Repeater/Coupler is suitable for handling switching operations between widely spaced sections prevailing in complex wiring systems. Here this device can also be used as a coupler in connection with a twin-core control line. The signals arriving via the line are amplified and retransmitted in the filtered X-10 signal circuit. Use & Applications
Use & Applications
Test your X-10 signals!
Commercial Info Quickly find noise and weak X-10 signals with this Signal Strength Indicator. This set is a must for anyone serious about X-10 troubleshooting
Features It send a constant P1 ON/OFF X-10 signal at a precise output voltage and measures the strength (voltage) of this signal. Plug the signal strength indicator into a wall outlet and send an X-10 command. The indicator will tell you the quality of the X-10 signal between the 2 locations. Has 5 signal strength levels showing the strength of the X-10 signal. High-frequency noise affecting the X-10 signal can be sensed with this device and can be neutralized by Coupler/Filters and Filters. It is good practice to test the complete system with the Signal Strength Indicator.
Use & Applications TEST: the strength of your X-10 signals the quality of X-10 path between 2 locations check for interference
Control just about anything in your house!
Commercial Info This module allows you to interface with the world! The Universal Module is used to control devices that would normally operate on low voltages, such as curtain controls, window openers, garden sprinkler systems,... The unit has a built-in beeper that can be used as an annunciator or additional wake up alarm when used with a Mini Timer (MT7222). It can be set to operate for momentary or sustained contact closure.
Features The Universal Module is used to control devices that would normally operate on low voltages, such as curtain controls, window openers, garden sprinkler systems,... The unit has a built-in beeper that can be used as an annunciator or additional wake up alarm when used with a Mini Timer Controller. It can be set to operate for momentary or sustained contact closure. The contacts are rated at 5A at 24V DC or 10A at 30V AC.
Use & Applications Low voltage control : Garage doors, Watering systems, Drapery control, Window openers, Electronic projects, Security, Signaling device,...
TWO-WAY PLC INTERFACE - TW7223
Design your own OEM applications for X-10 control!
Commercial Info The Two-Way Powerline Interface is a universal interface which allows any OEM product to transmit and receive data compatible with the X-10 system.
Features - Send and receive X-10 signals - Develop your own X-10 Compatible products or X-10 Home Automation System It plugs into an AC outlet and connects to the OEM product via a telephone jack. The Two-Way Interface can also read it's own incorporate error detection and contention resolution into his software or firmware.
Use & Applications If you know how to send and read RS232 type serial communication with your computer or from any other electronic device, you can develop and market your own software and/or hardware for use with X10 compatible systems without having to develop your own X10 communications hardware. This module is optically isolated. The timing critical nature of communication with this device requires low level hardware programming experience. It may also require dedicated microprocessor time. It is not recommended for casual programmers.
Easy adds motorization to new and existing draperies, vertical blinds and many shades.
Commercial Info Features Add-a-Motor fits all drapery and vertical blinds, and many shades. Simply remove tension pulley or other device on the window covering cord or chain. Motor attaches to loop end of cord or chain. Add-a-Motor resolves child safety problem related to exposed cords and chains. Many split-cords and chains can now be motorized. Use & ApplicationsAdds motorization to all new and existing draperies and vertical blinds, and many shades. Attaches to the window covering without modification. Fits all cords and bead-chains with loop-ends, and many split cords and chains. A simple dial allows you to adjust motor so it will automatically stop at the open and closed position that you prefer. Examples: Full open, closed, or any in-between. Remote control includes battery, and has a 50-foot "no-aim" range even through furnishings. Can traverse draperies up to 60 pounds and 12 feet wide. Can traverse, or rotate vertical blinds. Can lift and lower large shades. Plug-in ready, with compact size that conceals behind fabric or furniture. Compatible with most lamp timer-switches. Compatible with IBM Home Director, Honeywell Home Controller, and all other X-10 home automation systems.
Features
Advanced Drapery Control.
Commercial Info Enjoy the ultimate luxury and energy savings that only automatic drapery control can give you. Also keeps the sun away from your beautiful furnishings. Drapeboss uses advanced technology. It contains a microprocessor computer controlled gear-head motor, giving increased power and precision accuracy.
Features Timer opens and closes drapes at preprogrammed times Time controllable X-10 controllable Adjustable speed Adapts to most drapes and vertical blinds with pull cords Powerful motor controls heavy drapes Works on chain drapery cord systems and vertical blinds. Use & Applications Finally an affordable drapery controller that adapts to your existing drapes or vertical blinds that as has real automation capability. The built-in timer can schedule up to 6 timed movements within each 24 hr period. It can be set for full or partial open or close. 3 input terminals are available for connection to other control devices such as the X10 Universal module. Momentary or continuous contact inputs. LCD display shows time-of-day, programming display, and open/close status.
Use & Applications Finally an affordable drapery controller that adapts to your existing drapes or vertical blinds that as has real automation capability. The built-in timer can schedule up to 6 timed movements within each 24 hr period. It can be set for full or partial open or close. 3 input terminals are available for connection to other control devices such as the X10 Universal module. Momentary or continuous contact inputs. LCD display shows time-of-day, programming display, and open/close status.
X10 THERMOSTAT - TX15
Set specific temperatures with X10 commands Commercial Info Features Set modes with X10 commands Digital LED wall display with 32 settings Works with standard HVAC or heat pump systems Replaces existing thermostats without additional wiring The RCS Thermostats function as a standard thermostat and in addition allows remote X10 commands to set specific temperature set points and HVAC modes. Installation is simple.
Commercial Info
Set modes with X10 commands
Mount the HVAC control box near your HVAC system and replace your existing four wire (or more) thermostat with the RCS Thermostat. Includes Wall Display Unit, Control Unit,X10 2-Way Powerline Interface and cables.
This product will operate X10 products through 230V/50HZ
powerlines with the required TW7223E powerline interface, and needs a 12VDC
MULTI-PURPOSE I/O BOARD - LynXP
Commercial Info Features Automated computer or stand - alone X10 control of sprinkles, garage doors, HVAC systems, thermostats audio components and more.
Automated computer or stand - alone X10 control of sprinkles, garage doors, HVAC systems, thermostats audio
Works with X10 security systems and X10 sensors
Features 8DPDT relays, 8 digital inputs and 4 analog 8-bit
inputs for expanded control.
MULTI-PURPOSE RELAYS - RCX10 Commercial Info Features The X10 relay controller responds to standard X10 ON/OFF commands to control 4,8 or 16 independent DPDT relays. Four channel version can be set to any X10 housecode and one of four groups of sequential X10 unit codes (1-4,5-8,9-12,13-16). Eight channel version can be set to one of two groups of sequential unit codes(1-8,9-16). Available with latched, pulsed or momentary, 2 amp outputs. Requires the TW7223 Interface.
The X10 relay controller responds to standard X10 ON/OFF
RAIN SENSOR - GH502 Commercial Info Features The most reliable rain sensor available. Measures rainfall through water absorbing disks. They soak up water and dry out just like turf.
The most reliable rain sensor available. Measures rainfall through
Since the disks expand when wet, they depress a switch which breaks the circuit from the whatever controller you are using. Once the disks are dry, they contract and release the switch.
Smart! Simple click-stop settings adjust for rainfall in 1/8" increments up to 1". Adjustable ventilation holes control how fast the wet disks dry out. Includes 25 feet of 20 gauge 2 conductor wire and a short lead for n/o wiring
Commercial Info Features This equipment lets to monitor the values of The temperature, the environments' relative humidity and luminosity. These values are shown on a display with the indication of date and time. The unit lets to make the controlled variables' daily programming and to command till to 5 units (air conditioners, lamps, humidifiers, etc.) The user can set the minimum and maximum values of these variables and in case the controlled variable goes out this range, the unit commands the relative system (for that variable itself) to carry again the parameter inside the established limits. It can also have an alarm limit to monitor the wrong working of an equipment and to note emergency situations (for example the too high temperature in a room). The following functions are available for this unit:
This equipment lets to monitor the values of